Rigid ball bearings

single-row, thin section,

1600 series

Caution, prices written into the "€" column are your discount prices (if you are connected), or the general public prices (if you are not).

 

Catalog » Bearing And Ball Bearing Units NSK » Rigid ball bearings » Single-row, thin section, 1600 series

  • Stocks & Prices
  • Specification
  • Diagram

 

The last letter of the code (N or R) corresponds to the manufacturer identification.

 

Code Stk € Discount
code		 Dimensions (mm) Base load (kN) Speed limit rpm
d D B Dyn. C Stat. Co Grease Oil.
16001N
13,96  01 12 28 7 5.10 2.37 28000 32000
16002N
14,03  01 15 32 8 5.60 2.84 23000 28000
16003N
13,69  01 17 35 8 6.00 3.25 21000 24000
16004N
15,10  01 20 42 8 7.90 4.45 18000 20000
16005N
16,60  01 25 47 8 8.85 5.6 15000 18000
16006N
19,45  01 30 55 9 11.20 7.35 13000 15000
16007N
22,43  01 35 62 9 11.70 8.20 11000 13000
16008N
26,05  01 40 68 9 12.60 9.65 10000 12000
16009N
33,68  01 45 75 10 14.90 11.40 9000 11000
16010N
38,37  01 50 80 10 15.40 12.40 8500 10000
16011N
52,17  01 55 90 11 19.40 16.30 7500 9000
16012N
59,42  01 60 95 11 20.00 17.50 7100 8500
16013N
69,16  01 65 100 11 20.50 18.70 6700 8000
16014N
84,59  01 70 110 13 26.80 23.60 6000 7100
16015N
94,05  01 75 115 13 27.60 25.30 5600 6700
16016N
110,13  01 80 125 14 32.00 29.60 5300 6300
16017N
120,24  01 85 130 14 33.00 31.50 5000 6000
16018N
137,88  01 90 140 16 41.50 39.50 4800 5600
16019N
150,87  01 95 145 16 43.00 42.00 4500 5300
16020N
170,50  01 100 150 16 42.50 42.00 4300 5000
16021N
206,37  01 105 160 18 52.00 50.50 4000 4800
16022N
238,89  01 110 170 19 57.50 56.50 3800 4500
16024N
279,08  01 120 180 19 56.50 57.50 3600 4300
16026N
379,11  01 130 200 22 75.50 77.50 3000 3600
16028MN
853,60  01 140 210 22 78.00 79.50 2800 3400
16030N
530,10  01 150 225 24 87.00 91.00 2600 3100
16030MN
848,12 
16100N
14,73  01 10 28 8 5.10 2.37 28000 32000
16101N
14,71  01 12 30 8 5.10 2.39 28000 32000

 

éclaté roulement 6000

 

 

Rigid ball bearings can accommodate radial and axial loads in both directions. Due to their low frictional torque, they are suitable for high-speed applications. These bearings are particularly suitable for applications calling for a low level of noise and vibration. Rigid ball bearings are classified by type, as indicated below.

A specific amount of grease is integrated into the sealed bearings.
éclaté roulement 4000

From a size and function standpoint, double-row rigid ball bearings correspond to a pair of single-row ball bearings.

This type of bearing must not be used if alignment faults are to be corrected.

schema roulement
Specifications ZZ Type
(shield)		 VV Type
(non-contact seal) 		DDU Type
(contact seal type)
Frictional
torque		 Low Low Higher than ZZ and VV types due to the seal contact
Suitable for
high speeds 		Good Good Limited by seal contact
Grease
retention		 Good Higher than the ZZ type Slightly higher than the VV type
Dustproof Good Higher than the ZZ type Excellent
Impermeability Not suitable Not suitable Good
Temperature
range *		 -10 to +110° C -10 to +110° C -10 to +100° C

* The temperature ranges indicated apply to standard bearings. If a heat or cold-resistant grease is used and another type of seal, the temperature ranges can be extended.
Do not hesitate to contact us for these applications.

 

 

Rigid ball bearings generally come with a pressed steel cage. Machined brass cages are used for large bearings and high-speed applications. For certain applications thermoplastic or thermosetting resin cages also exist.

 

Standard type of cage used for bearings

 

Series Pressed
metal cage		 Machined
brass cage		 Series Pressed
metal cage		 Machined
brass cage		 Series Pressed
metal cage		 Machined
brass cage
60 6000 / 6040 6044 / 6080 64 6403 / 6418 6420 / 6426 160 16001 / 16026 16028 / 16060
62 6200 / 6236 6238 / 6248 68 6800 / 6830 6832 / 6860 160 16100 / 16101  
63 6300 / 6332 6334 / 6340 69 6900 / 6928 6930 / 6980      

 

 

Single-row, rigid ball bearings allow for slight misalignment of the shaft and housing. The acceptable misalignment fault for this type of bearing depends on the dimension of the bearing, the internal radial clearance after assembly and the load on the bearing. Generally speaking, angle values of 2 to 10 minutes are acceptable.

Double-row, rigid ball bearings only allow for very slight misalignment of the shaft and housing.

 

The most common suffixes for rigid ball bearings and the corresponding definitions.

 

Suffix Definition
C2  Less radial clearance than usual
Néant  Normal CO clearance
C3  Greater clearance than usual
C4  Greater clearance than C3 clearance
C5  Greater clearance than C4 clearance
CM  Radial clearance for silent electric motor
D  Synthetic rubber single-side contact seal
DD  Synthetic rubber double-side contact seal
DDU  Synthetic rubber double-side contact seal
DDW  Synthetic rubber double-side low torque contact seal
DU  Synthetic rubber single-side contact seal
DUN  Synthetic rubber single-side contact seal plus groove for snap ring
DUNR  Synthetic rubber single-side contact seal plus groove and snap ring
E  Quiet bearing
ER  Quieter than E
Suffix Definition
M  Solid brass cage
MC2  Less radial clearance than usual
MC3  Normal radial clearance (miniature ball bearings and small bearings)
MC4  Greater radial clearance than MC3 clearance
MC5  Greater radial clearance than MC4 clearance
MC6  JGreater radial clearance than MC5 clearance
V  Synthetic rubber labyrinth seal - no contact on one side
VV  Synthetic rubber labyrinth seal - no contact on both sides
Z  Metal shield on one side
ZN  Metal shield on one side plus groove for snap ring
ZNR  Metal shield on both sides plus groove and snap ring
ZS  Metal shield on one side for miniature bearings
ZZ  Metal shield on both sides
ZZS  Metal shield on both sides for miniature bearings

 

 

Technical drawing of bearing